Best Rust Inhibitor? - Hot Rod Forum
2004年6月4日 · 2. Stop the water (as much as possible) from entering body cavities. Remember condensation is not quite the same as a rain storm, but it causes fuel tanks and lots of other things to get rust holes through the bottom of the tank. 3. Stop the water (and dust) from gathering in the cracks and crevises.
Best Rust Inhibitor? | Page 3 - Hot Rod Forum
2004年6月1日 · The phosphoric acid is present in a quantity of between 2 and 3.2%; the Zn (HPO.sub.4).sub.2 in a quantity of between 1.1 and 2%; and the Zn (NO.sub.3).sub.2 in a quantity of between 7 and 12%. Any deficiency in one of these three latter components results in a lower initial reaction rate and the formation of a final incoherent protective layer ...
The Ospho Solution.. (rust removal) - Hot Rod Forum
2010年3月30日 · The way I look at it ,On the east coast cars can rust within five yrs when new, so anything over that is great. You got to remember with heavy pitted rust there isn't much metal left.the best thing is to replace it.(but that gets expensive) or clean up the rust (like my trim holes) and glue some metal to the back side for strength.
rust inhibitor experience - Hot Rod Forum
2011年1月28日 · 200horse. 57 posts · Joined 2010. #11 · Feb 7, 2011. try anti rust by tntrustremover.com its a waterbase enviormantally product that keeps rust from returning. I spayed my car and so far no rust has returned. They say before you paint it you wash it down with hot soapy damp cloth or sponge. good luck.
OSPHO factory response - Hot Rod Forum
2010年2月24日 · Response: Yes, the Ospho will be totally neutralized by reaction with both the rust particles and the steel underneath. A quick water rinse after it has dried (remember, Ospho is water-based) will remove any trace of reaction particles (dust-like) and make sure the surface is in perfect condition for priming. Stephen L. Pitcher.
cleaning rust off crankshaft - Hot Rod Forum
2007年1月11日 · Polishing crank at home. Get some 600 wet or dry sandpaper and cut it into strips the same width as the crank journal. Wrap this strip around the journal with the abrasive against the journal and secure it in place with a small strip of tape, snug but not tight. Make the strap from a thin piece of leather or peel the outer layer of ply from a ...
por 15 vs. rust bullet - Hot Rod Forum
2007年7月9日 · when applying por 15 it goes on thick, and when dry it is almost like a plastic cover over the metal amd imder UV light, it turns different colors. Rustbullet. By far the best rust penitrator/gaurd i have used, and seen, i welded a few patches on the floor of my pickup last february, and applyed the paint, and you can literally watch it ...
Flash Rust after sand blasting - Hot Rod Forum
2011年6月19日 · Flash Rust after sand blasting. When I blast parts in my direct pressure blaster, in a day or so, I get a little bit of flash rust on one or two very small areas of of the parts I blast. My normal step it blast during the week and prime and paint during the weekend when I …
Media blast with walnut shells or soda blast? | Hot Rod Forum
2007年10月5日 · Hold Tight Solutions should be used after blasting with any media. I am a soda blast contractor (5 years now), distributor of Hold Tight Solutions, Natrium Products soda blast media, The Soda Works soda blast equipment, KBS Coatings and New Age crushed glass media. I am at 410-271-2652 and www.ChesapeakeSodaClean.com.
Mercury Flathead V8 help - Hot Rod Forum
2013年6月11日 · I have a 1953 Mercury Flathead V8, I run 160 degree thermostats i just installed a half fan shroud and i run 50/50 antifreeze along with a rust inhibitor. i also have a 12" electric fan mounted on the front of the radiator.